Secret Cam sticky. - Performance Forum

Forum Post / Reply
You must log in before you can post or reply to messages.
Secret Cam sticky.
Friday, October 14, 2005 5:18 PM
So many question on this subject we should just make a sticky. Here is the info i got along time ago:

Well, I guess I will let the cat out of the bag now. For over a year now I have been speculating about using Quad4 cams in the LD9 as upgrades. The first idea cam from here -->http://babcox.com/editorial/ar/ar40032.htm

Since the 95 spec cam has the required cam position sensor lobe and the power steering drive, it should work.

Next I found the specs for the Mantapart street cams:
Mantapart Mild Cams Specs
198 degrees @ .050" with .360" lift for the intake
201 degrees @ .050" with .374" lift for the exhaust


What I saw was this:
1995 Cam Specs
200 degrees @ .050" with .360" lift for the intake
200 degrees @ .050" with .360" lift for the exhaust
LD2 (1990+) Cam Specs
200 degrees @ .050" with .375" lift for the intake
200 degrees @ .050" with .375" lift for the exhaust

Note the 95 intake and the LO Exhaust! Pretty darn close eh!

So I was always wanting to try this theory out, but was unable to find the time or courage to do it. That is where my buddies Mark and Colin came in. Mark really wanted to do this, so he went to alot of effort to find the cams. Colin (V6HO) came in and did the install into Mark's car, and it ran great with no codes.

Next up was Aaron's (Pimpin2da4) car the day before he left for the bash. Judging by him being the only NA car in the Quick 8, I think that the cams show what is possible.

I thought it more prudent to share this with everyone so the whole can benefit from the knowledge gained.

Now, everyone wanting to do this, hit up your local junkyard and get tuning!
www.GMPartsDirect.com

24574239 Intake camshaft for LG0(95 2.3DOHC) $197.64
22545390 Exhaust cam for LD2(Pre-95 2.3DOHC) $197.64


12355988 - Intake or exhaust cam carrier gaskets (upper and lower)
12363173 - Intake or exhaust cam carrier gaskets (upper and lower)
24575512 - Tensioner. Not required, but if you have timing chain noise..change this. Also, be sure you are familiar with how this part works because it has to be pre-loaded once installed to snug up the timing chain.
24575513 - Tensioner shoe. This will probably break when you remove, so change it anyway.
24575255 - Guide. Not required unless yours are worn.
24575257 - Guide. Same as above.
24575256 _ Guide. Same as above.
992704 - Assembly Lube. Good idea to coat the cam lobes and the carriers where the cam contacts with this stuff.
992869 - Oil supplement. The GM manual calls for this stuff when you do the cams.
12360464 - I think this # is the timing chain cover gasket. (optional)
245752453 - I think this is rthe # for the water pump gasket kit. This is only required if you are doing your water pump. I did my water pump and thermostat at the same time as the cams
----------CAM UPGRADE----------

The intake cam is from a 1995 (only) 2.3L Quad 4 engine.. the eighth digit in the VIN is a letter D. Can be found in 1995 Cavalier Z24's, Sunfire GT's, and Olds Achievas. Brand new, it's


--->GM part #24574239($197.64). If you're looking under hoods, the casting number on the cam is 245/742 (which IS the same number as the 2.4L LD9, but has 0.360" of lift), and the casting number on the cam housing/carrier is 24574057.

The exhaust cam is from a 1990-94 (only) 2.3L Quad 4 engine.. VIN D as well. Can be found in 90-94 Grand Am's, Olds Cutlass, Calais, Acheiva, and Buick Skylark. Brand new, it's
Melling MC832 from Autozone

--->GM part #24570698 or #22545390 (a little confusion there)($197.64). The cam casting numbers are 255/455 (which IS the same number as the HO cams, but only has 0.3750" of lift, not 0.410") and the housing/carrier itself is 22542963.

If you are going to do this swap, here is the complete list of gaskets required. I bought them not as kits because I didn't want to be left over with gaskets I didn't need. When I compared costs briefly with Nate, it would appear that I didn't spend more than him and may have even saved some money because the kit he got had the head gasket, and I didn't get a head gasket. YOU DON"T NEED A HEAD GASKET FOR THE CAM SWAP! I also bought a new timing chain cover gasket, but you don't need to. Unless yours is leaking, you can re-use it. If your car is pre 1997, you may want to change it while you are in there anyway. Here are the GM part numbers:

12355988($8.46) - Intake or exhaust cam carrier gaskets (upper and lower)
12363173($10.30) - Intake or exhaust cam carrier gaskets (upper and lower)
24575512($30.00) - Tensioner. Not required, but if you have timing chain noise..change this. Also, be sure you are familiar with how this part works because it has to be pre-loaded once installed to snug up the timing chain.
24575513(3.00) - Tensioner shoe. This will probably break when you remove, so change it anyway.
24575255($12.23) - Guide. Not required unless yours are worn.
24575257($12.23) - Guide. Same as above.
24575256($12.23) _ Guide. Same as above.
992704($NA) - Assembly Lube. Good idea to coat the cam lobes and the carriers where the cam contacts with this stuff.
992869($NA) - Oil supplement. The GM manual calls for this stuff when you do the cams.
12360464($28.29) - I think this # is the timing chain cover gasket. (optional)
245752453($NA) - I think this is the # for the water pump gasket kit. This is only required if you are doing your water pump. I did my water pump and thermostat at the same time as the cams.

From me to you guys a complete manual on what to do and what not to do and how to swap cams in a 2.4 and what tools are needed and what size.

Don't judge it and stupid comments and grammar checks are not necessary, I think there isn't anything more to add to it.
Just tell me how you like it?

Enjoy It is a little long, sorry.
Camshaft swap



2004 Grand Prix GTP (Competition Group)
SOLD-->1999 Z24 5M-#30 to register on JBO
"You can please some of the people some of the time but you can't please all the people'
all the time



Re: Secret Cam sticky.
Saturday, October 15, 2005 12:53 AM
some of that has been taken off of the NY-J body website. so... don't take all the credit otherwise yeah it's a damn good writeup. Anyone else? this has my vote for a sticky.



Re: Secret Cam sticky.
Saturday, October 15, 2005 1:13 AM
how secret will it be if its stickied to the top of the page ?




Re: Secret Cam sticky.
Saturday, October 15, 2005 1:16 AM
^^^ haha nice



Re: Secret Cam sticky.
Saturday, October 15, 2005 3:11 AM
The Other Matt wrote:how secret will it be if its stickied to the top of the page ?


Honestly, it's not even a secret anymore. It's been so exploited it's not even funny.

Other than that, good write up.



www.kronosperformance.com / 732-742-8837

Re: Secret Cam sticky.
Saturday, October 15, 2005 4:49 AM
yeah good write up
when i first read the title i thought he meant the cam itself was sticky.....its early in the morning



Re: Secret Cam sticky.
Saturday, October 15, 2005 5:35 AM
I found 1 small mistake :
Quote:

24574239 Intake camshaft for LG0(95 2.3DOHC) $197.64


LGO is the HO engine.
LGO-W41 is the W41 engine

So I can't believe GM put the LGO rpo code for the 95.



Gilles
2.3 Ho

Re: Secret Cam sticky.
Saturday, October 15, 2005 12:32 PM
Inari (Protected by Pedro) wrote:some of that has been taken off of the NY-J body website. so... don't take all the credit otherwise yeah it's a damn good writeup. Anyone else? this has my vote for a sticky.

For your information. That was taken from the post that happen almost 3 years ago. NY-J-Body took that information from that post. What i posted there was the first message from that post. I have had my cams for almost 3 years now. So NY JBO needs to give credit for that post. Also you have been here long enough to give that statement. I know this because i have been here since JBO site began.


2004 Grand Prix GTP (Competition Group)
SOLD-->1999 Z24 5M-#30 to register on JBO
"You can please some of the people some of the time but you can't please all the people'
all the time


Re: Secret Cam sticky.
Saturday, October 15, 2005 4:30 PM
sticky



Re: Secret Cam sticky.
Sunday, October 16, 2005 2:09 PM
The Other Matt wrote:how secret will it be if its stickied to the top of the page ?


just as secret if you had the search button directly linked to it, maybe 15 people could find it.




Re: Secret Cam sticky.
Sunday, October 16, 2005 3:57 PM
Mylife75 (ajose) wrote:
Inari (Protected by Pedro) wrote:some of that has been taken off of the NY-J body website. so... don't take all the credit otherwise yeah it's a damn good writeup. Anyone else? this has my vote for a sticky.

For your information. That was taken from the post that happen almost 3 years ago. NY-J-Body took that information from that post. What i posted there was the first message from that post. I have had my cams for almost 3 years now. So NY JBO needs to give credit for that post. Also you have been here long enough to give that statement. I know this because i have been here since JBO site began.



point made. Totally sticky worthy.




Re: Secret Cam sticky.
Sunday, October 16, 2005 4:30 PM
say it again, sticky this is truly good information



Re: Secret Cam sticky.
Sunday, October 16, 2005 8:30 PM
doing the swap friday




Sorry...
You have been banned from posting on this site as of 2005-09-21

00:33:32. This ban will expire 2005-09-28 00:33:32 Pacific Time.
Reason: Comments over the top regarding Jordan Kruger and other members in Versus. Also, if you have a problem with a member e-mailing you, do not bring it into the forums.

If you believe this to be in error, please contact us.
Re: Secret Cam sticky.
Tuesday, November 15, 2005 6:26 PM
Excelent info... anyway.


___________________________
MAKING MY DREAMS A REALITY
Visit my cardomain site !!!

ELIOT. Now.....boosted.

Re: Secret Cam sticky.
Sunday, November 20, 2005 9:43 AM
great info!



Portage, MI
Re: Secret Cam sticky.
Monday, November 21, 2005 1:22 PM
It is asked all the time so a post with the title like this and the info i thought would help with questions constantly asked.


2004 Grand Prix GTP (Competition Group)
SOLD-->1999 Z24 5M-#30 to register on JBO
"You can please some of the people some of the time but you can't please all the people'
all the time


Re: Secret Cam sticky.
Friday, December 02, 2005 8:59 AM
May be a stupid question. But will this swap work in a 2.2 ecotec...or is it for a 2.4 in lets say the 99 up Z24's...


thanx



Re: Secret Cam sticky.
Friday, December 02, 2005 9:27 AM
for all 2.4 engines 96-02


2004 Grand Prix GTP (Competition Group)
SOLD-->1999 Z24 5M-#30 to register on JBO
"You can please some of the people some of the time but you can't please all the people'
all the time


Re: Secret Cam sticky.
Friday, December 09, 2005 7:34 AM
Whoo Hoo it is a sticky.


2004 Grand Prix GTP (Competition Group)
SOLD-->1999 Z24 5M-#30 to register on JBO
"You can please some of the people some of the time but you can't please all the people'
all the time


Re: Secret Cam sticky.
Sunday, December 11, 2005 9:08 PM
thanks alot for the cam info guys, really appriciate it
Re: Secret Cam sticky.
Monday, December 12, 2005 5:36 AM
I remember when this information was first posted back in 2002. Then i did the swap in early 2003. I still have some of the replies to that post on my computer.


2004 Grand Prix GTP (Competition Group)
SOLD-->1999 Z24 5M-#30 to register on JBO
"You can please some of the people some of the time but you can't please all the people'
all the time



Re: Secret Cam sticky.
Sunday, January 01, 2006 4:00 PM
so what kind of gains can you expect from these cams? would they be recommended for doing a turbo engine?


HP Tuners | Garrett T3/T04B | 2.5" Charge Pipes | 2.5" Downpipe | 650 Injectors | HO Manifold | Addco front/rear | Motor Mounts | HKS SSQV | Spec stage 3 | AEM UEGO Wideband | Team Green LSD | FMIC | 2.3 cams | 2.3 oil pump swap | 280WHP | Now ECOTECED

Re: Secret Cam sticky.
Wednesday, January 04, 2006 2:17 PM
hey so if i do the cam swap do i need to change the computer? and how hp gain will i be expecting?one more question, where could i find valvespring and retainers for the 2.4(performance....thanx Dj


Re: Secret Cam sticky.
Thursday, January 05, 2006 5:57 AM
^^ Nope, dont have to change your computer..

Are you talking about aftermarket springs and retainers or what?









~2014 New Z under the knife, same heart different body~
______________________
WHITECAVY no more
2012 numbers - 4SPD AUTOMATIC!!
328 HP
306 TQ
Re: Secret Cam sticky.
Saturday, January 07, 2006 3:56 PM
ya after market valve spring and retainers...can you help me.....thanx Dj


Forum Post / Reply
You must log in before you can post or reply to messages.

 

Start New Topic Advanced Search