If this k brace will work with v6 swap count me in.
In for updates!
PRND321 Till I DIE
Old Motor: 160whp & 152ft/lbs, 1/4 Mile 15.4 @88.2
M45 + LD9 + 4T40-E, GO GO GO
Interested in the cooling tank
specs and prices on that would be greatly appreciated!
why dont you do us all TC headed guys a favor and make some god damn exhaust manifold gaskets...
ill take
Manual steering rack- This is a gutted and re-engineered rack meant for non PS systems.
Thermostat relocation Kit- ld9
MP-62 Intercooled 2.9" Pulley
OverKill All The Way!!!!! wrote:Yes, I have ordered the material to build 10 of these units.
These are going to be made out of steel to be structural. Aluminum would give way to much. These will be fully welded without heim joints and also powder coated.
We are making 10 of these for the first run. The first run will be 89.99 shipped. We are also making these fit the AUTO's.
Stay tuned.
Mark
Well thats quite the jump.....im out..
Sorry about that one Philly that was actually my fault I fat fingered the GP post.
It should have read $150 shipped in the US.
My apologies for the mix up, the GP thread has been fixed.
Club Jeffie, Yea we can make that. Text or Call(908)866-1882
im interested in the ld9 sheetmetal intake manifold!
It would be awesome to see some oil cap for the ECOs. Can't wait to see them.
"United by Individuality"
"If life is a joke, why aren't we laughing?"
"Normality depends on one's perception of reality."
http://www.cardomain.com/ride/3820803
I really need some input on the design. So many people want so many different things. Once I get a sure set design I will have 10 sets made, welded, anodized and engraved. We are looking to make top notch parts so we need set in stone ideas so that there are not so many design changes.
Mark
What is everyone looking for on the coolant tanks? Round? Square? Sensors? Hoses? AN fittings? ETC...
http://www.overkillengineeringmotorsports.com/
Have u seen the old vulcan turbo tanks, the one that Whitecavy has?
boostedz24
Id probably be in for a catch can w/ petcock for a drain. Also be in for a vented oil cap if it could be made low profile?
OverKill All The Way!!!!! wrote:Revised Camber plates and Wateroutlets for LD9 are coming soon. Anything else you guys needs made better?
Mark
Thank YOU!!
~2014 New Z under the knife, same heart different body~
______________________
WHITECAVY no more
2012 numbers - 4SPD
AUTOMATIC!!
328 HP
306 TQ
OverKill All The Way!!!!! wrote:I really need some input on the design. So many people want so many different things. Once I get a sure set design I will have 10 sets made, welded, anodized and engraved. We are looking to make top notch parts so we need set in stone ideas so that there are not so many design changes.
Mark
What is everyone looking for on the coolant tanks? Round? Square? Sensors? Hoses? AN fittings? ETC...
I'd honestly like the one you made to fit in the corner behind the head light. With sensors and hooks to stock lines id be in for one!
Wanna make my intake sit right behind it
OEM Corner tank pwease...
Not Vulcan poop
Matt Tirpak wrote:OEM Corner tank pwease... Not Vulcan poop
sensor and works for stock hoses pwease
Matt Tirpak wrote:Matt Tirpak wrote:OEM Corner tank pwease... Not Vulcan poop
sensor and works for stock hoses pwease
I dig that corner tank. Would love it to accept stock hoses and sensor of course.
BeardLife /
Club Awesome Reject Blog