***Parting out*** (M62 Supercharger kit, Carbon fiber hood and moar) - Mid East Region Forum

Forum Post / Reply
You must log in before you can post or reply to messages.
***Parting out*** (M62 Supercharger kit, Carbon fiber hood and moar)
Friday, April 13, 2012 5:06 PM
Yep, everyone has to do it at some point or another. Wanted to first offer these great parts to the members of J-Body before I put them on E-bay. I have learned so much since i've been a member here, and I know you guys will have as much fun with these parts as I did. Local Pickup would be preferred to save you and me money but shipping is fine, On to the list:

Complete M62 Supercharger "kit". $1800 shipped This was not a GMPP kit, these are parts pulled from a S/C Cobalt. WILL NOT BE PARTING OUT THE KIT. Buyer takes all

List of parts
-Cobalt M62 Supercharger (Has been rebuilt with new S/C coupler, and has new S/C fluids and seals, has the noise ports mod done)
-Cobalt Intake Manifold W/ gaskets (Has dual pass end plate mod done and Intake air temperature mod done, see pics)
-Stock S/c Pulley
-Water to air heat exchanger
-Brand New Bosch Pump with pigtail
-Cobalt Bracket to hold the bosch pump
-Cobalt heat exchanger remote reservoir
-Idler pulley (takes place of the stock tensioner)
-Cobalt belt tensioner
-Stock Cobalt SS S/C injectors
-2002 cavalier fuel rail (to make the injectors fit properly
-2002 Fuel lines if it makes a difference
-Cobalt SS Map Sensor with pig tail ..... was not cheap
-Cobalt belt with one rib shaved off (so it will work with the cavalier accessories)
-Cobalt Upper Radiator hose
-Custom throttle body adapter (need this to use cavalier throttle body)
-Cobalt Brake booster vacuum line
-S/C Flashed PCM*
-Longer bolts for alternator

*Bonus Parts*
-Supercharged Badge from cobalt SS
-2.2L Supercharged IDI cover and other random stickers
-Special tool to put the belt on
-additional coolant pipes if you need them

*Parts you will need to run*
-Colder range spark plugs
-93 octane
-a lead foot


-All Bolts and gaskets have been labeled and bagged for ease of installation. THIS IS THE INSTRUCTIONS TO INSTALL-------> READ THEM there is a couple of really important steps like shaving the block down for the cobalt tensioner. Also in the pics of the supercharger I noticed the 3.1" pulley is still installed on the supercharger that will be taken off and the stock pulley will be put back on.

*S/C Flashed PCM has one issue. Will run and drive your car just fine ran mine off of it a year and a half with no problems, will just set a check engine light for a/c pressure sensor circuit fault, and fuel tank pressure sensor circuit fault. The 5v reference wires on these two circuits are dead. You can get the check engine light to turn off with a trick. Cut the two wires on your harness going to those pins on the PCM, and use proper crimps with heat shrink to tie those wires to a working 5v reference. I think i used the throttle body 5v circuit on my car. Boom check engine light is gone and your a/c works again, YOUR WELCOME.



This pic should give you an idea of how these hoses are installed.





ZZP? 3.1" Pulley W/ quick adapter hub- $50 + Shipping









S/C Pulley Puller - $50 + Shipping









Carbon Fiber "turbo sport" Hood for 1995 to 2002 Cavaliers - $400 + Shipping


See my cardomain to see how its looks installed






Glow Shift Gauges - $10 + Shipping for boost $20 + Shipping for Volts and Oil Pressure gauges

Currently installed in car so no pics this moment Im going to uninstall them right after Im done typing this pics should be up tonnight.

-Boost ( button damaged. Button works great its just ultra sensitive and sometimes changes colors when going over a bump.)
-Volts
-Oil Pressure







Custom Made Fiberglass Dash $40 + Shipping Made to accept all 52 mm gauges





CarDomain http://www.cardomain.com/id/TMald123

Re: ***Parting out*** (M62 Supercharger kit, Carbon fiber hood and moar)
Friday, April 13, 2012 5:16 PM
Instructions for supercharger installation http://www.mediafire.com/?0vjbinjtasb



CarDomain http://www.cardomain.com/id/TMald123
Re: ***Parting out*** (M62 Supercharger kit, Carbon fiber hood and moar)
Friday, April 13, 2012 5:18 PM
PM'ed you regarding the dash.



Re: ***Parting out*** (M62 Supercharger kit, Carbon fiber hood and moar)
Friday, April 13, 2012 5:32 PM
do you still have the same rims as in your sig? if so i might be intrested
Re: ***Parting out*** (M62 Supercharger kit, Carbon fiber hood and moar)
Friday, April 13, 2012 5:40 PM
I do but im not selling them right now



CarDomain http://www.cardomain.com/id/TMald123
Re: ***Parting out*** (M62 Supercharger kit, Carbon fiber hood and moar)
Friday, April 13, 2012 5:44 PM
How well does the hood fit, is there any damage and what would shipping be like to: Sumas, WA 98295

Also interested in the pulley puller.
Re: ***Parting out*** (M62 Supercharger kit, Carbon fiber hood and moar)
Friday, April 13, 2012 6:00 PM
Sale Pending on the dash



CarDomain http://www.cardomain.com/id/TMald123
Re: ***Parting out*** (M62 Supercharger kit, Carbon fiber hood and moar)
Friday, April 13, 2012 6:06 PM
Philly D wrote:

How well does the hood fit, is there any damage and what would shipping be like to: Sumas, WA 98295

Also interested in the pulley puller.


PM'd



CarDomain http://www.cardomain.com/id/TMald123
Re: ***Parting out*** (M62 Supercharger kit, Carbon fiber hood and moar)
Friday, April 13, 2012 11:50 PM
I want the 3.1 pulley and hub. Pm with payment options. Also do you make to Columbus area? If so I might pick it up off you if not I can just have you ship it.





Re: ***Parting out*** (M62 Supercharger kit, Carbon fiber hood and moar)
Saturday, April 14, 2012 12:29 AM
If only this couldve waited another month, I'd be all over that kit. Birthday is next week, who knows what could happen GLWS and if I get the cash ill be back



Re: ***Parting out*** (M62 Supercharger kit, Carbon fiber hood and moar)
Saturday, April 14, 2012 7:09 AM
interested in parting out just the h/e and the parts needed to install it?

Re: ***Parting out*** (M62 Supercharger kit, Carbon fiber hood and moar)
Saturday, April 14, 2012 11:50 AM
Not really interested in parting out the kit sorry




CarDomain http://www.cardomain.com/id/TMald123
Re: ***Parting out*** (M62 Supercharger kit, Carbon fiber hood and moar)
Saturday, April 14, 2012 11:52 AM
Hmmm for some reason this kit looks awfully familiar

GLWTS, I hope the kit served you well over the years you had it instaled!


12.770 @ 111.99 Intercooled Eaton M62


Re: ***Parting out*** (M62 Supercharger kit, Carbon fiber hood and moar)
Saturday, April 14, 2012 5:48 PM
haha, I was wondering if you were going to notice. How did the corvette work out? Sad to see it go have had lots of fun with it and I got a lot of complements, however its time to move on to the next project.



CarDomain http://www.cardomain.com/id/TMald123
Re: ***Parting out*** (M62 Supercharger kit, Carbon fiber hood and moar)
Saturday, April 14, 2012 5:53 PM
Hood is sold



CarDomain http://www.cardomain.com/id/TMald123
Re: ***Parting out*** (M62 Supercharger kit, Carbon fiber hood and moar)
Saturday, April 14, 2012 7:37 PM
MRThompson (jrthompson) wrote:

I want the 3.1 pulley and hub. Pm with payment options. Also do you make to Columbus area? If so I might pick it up off you if not I can just have you ship it.


i'll pm since you missed me.





Re: ***Parting out*** (M62 Supercharger kit, Carbon fiber hood and moar)
Saturday, April 14, 2012 7:42 PM
03 Cavalry wrote:

Hood is sold
This was a mistype. Dash is sold. Hood is still for sale




CarDomain http://www.cardomain.com/id/TMald123
Re: ***Parting out*** (M62 Supercharger kit, Carbon fiber hood and moar)
Saturday, April 14, 2012 8:02 PM
3.1" pulley and quick hub sold



CarDomain http://www.cardomain.com/id/TMald123
Re: ***Parting out*** (M62 Supercharger kit, Carbon fiber hood and moar)
Sunday, April 15, 2012 12:15 AM
whats the rotors look like on the charger im considering puttin it on my lss


RIP Cpl Derek Kerns And Cpl Robby Reyes
24th MEU VMM-261 (REIN) V22 Crewchiefs
11 April 2012 Morocco (African Lion)
Re: ***Parting out*** (M62 Supercharger kit, Carbon fiber hood and moar)
Sunday, April 15, 2012 8:56 AM
I don't frequent these forums as often as I used to but it caught my eye The vette is working out well and is sorted out for the most part. Definetly quick but there are certain things I miss about the cavy (especially the sleeper effect), everyone expects the vette to be fast when they hear it idle. Glad to hear it worked out for you!

03 Cavalry wrote:

haha, I was wondering if you were going to notice. How did the corvette work out? Sad to see it go have had lots of fun with it and I got a lot of complements, however its time to move on to the next project.



12.770 @ 111.99 Intercooled Eaton M62


Re: ***Parting out*** (M62 Supercharger kit, Carbon fiber hood and moar)
Sunday, April 15, 2012 1:41 PM
Cavi2Sunfire wrote:

whats the rotors look like on the charger im considering puttin it on my lss

Rotors have their usual wear and tear on them, but made 12 lbs on a cold day easily with the 3.1" pulley. I rebuilt the supercharger with a new coupler and put new s/c oil in it, and include the extra I have in the kit, and i put new seals on on the s/c.



CarDomain http://www.cardomain.com/id/TMald123

Re: ***Parting out*** (M62 Supercharger kit, Carbon fiber hood and moar)
Sunday, April 15, 2012 4:29 PM
well ill let you know my plan was to trade my 03 lss on a duramax to tow the sunfire but i want a fun daily at the same time lol so this is def tempting


RIP Cpl Derek Kerns And Cpl Robby Reyes
24th MEU VMM-261 (REIN) V22 Crewchiefs
11 April 2012 Morocco (African Lion)
Re: ***Parting out*** (M62 Supercharger kit, Carbon fiber hood and moar)
Monday, April 16, 2012 4:26 PM
Wanted to update the sales list, and Im adding 2 items for sale, wish i still had premium to edit my posts!

Items still for sale
- RK Sport Underdrive pulley for Ecotec engines $50 + shipping Comes WITH BELT (New to list)
- 3 gauge A-Piller piece $30 + Shipping (Brand new)
- 95-2002 carbon fiber turbo sport hood $400 plus shipping
- S/C pulley puller and installation tool $50 shipping
- Glow Shift Gauges 52mm white face with 7 color setting- Boost $10 + Shipping ( button damaged. Button works great its just ultra sensitive and sometimes changes colors when going over a bump.)
-Volts $20 + Shipping
-Oil Pressure $20 + Shipping



Items sold
- 3 gauge dash
- 3.1" pulley and quick change hub

If you need pics of underdrive pulley or 3 gauge A-piller piece PM me






CarDomain http://www.cardomain.com/id/TMald123
Re: ***Parting out*** (M62 Supercharger kit, Carbon fiber hood and moar)
Thursday, April 19, 2012 9:45 AM
recieved parts quickly, good seller.




Re: ***Parting out*** (M62 Supercharger kit, Carbon fiber hood and moar)
Friday, April 27, 2012 5:26 AM
Bump, stuff will be going to ebay this weekend last chance to get this stuff directly from me. Will post link to auctions, AM OPEN TO OFFERS.

Items still for sale
- M62 S/C Kit (see first post for info) $1800
- RK Sport Underdrive pulley for Ecotec engines $50 + shipping Comes WITH BELT (New to list)
- 3 gauge A-Piller piece $30 + Shipping (Brand new)
- 95-2002 carbon fiber turbo sport hood $400 plus shipping
- S/C pulley puller and installation tool $50 shipping
- Glow Shift Gauges 52mm white face with 7 color setting- Boost $10 + Shipping ( button damaged. Button works great its just ultra sensitive and sometimes changes colors when going over a bump.)
-Volts $20 + Shipping
-Oil Pressure $20 + Shipping



Items sold
- 3 gauge dash
- 3.1" pulley and quick change hub

If you need pics of underdrive pulley or 3 gauge A-piller piece PM me






CarDomain http://www.cardomain.com/id/TMald123
Forum Post / Reply
You must log in before you can post or reply to messages.

 

Start New Topic Advanced Search