Not a problem guys, let me see what I can get done asap.

http://www.overkillengineeringmotorsports.com/

Measurements for Tein Basics-

Fronts:


Rears:






Built 94-97 head for sale: http://www.j-body.org/classifieds/detail/47069/

Do you need the measurements for Koni's??




Jason
99 Z24 Supercharged
157hp/171tq - NA
LD9 for Life

problem, if those are just like the held motorsports ones, which they look to be, you will not be able to adjust the struts, at least not the tokico d-specs. i have the held motorsports mounts in the back and i cannot adjust my rear struts because the mount has the piston rod too far into the trunk so the key wont fit to adjust them.



12.33 @ 111.67 mph [Oct 2009]
Dyno'd on 08/02/09 - Mustang Dyno:
327.6 WHP 333.6 WTQ [10.1 AFR]

evilmonkitar wrote:problem, if those are just like the held motorsports ones, which they look to be, you will not be able to adjust the struts, at least not the tokico d-specs. i have the held motorsports mounts in the back and i cannot adjust my rear struts because the mount has the piston rod too far into the trunk so the key wont fit to adjust them.

To me if that is the case I would think it would make the rear of the car sit lower than it should.



FU Tuning

I am almost done with it. hang in there guys.

M

http://www.overkillengineeringmotorsports.com/

evilmonkitar wrote:problem, if those are just like the held motorsports ones, which they look to be, you will not be able to adjust the struts, at least not the tokico d-specs. i have the held motorsports mounts in the back and i cannot adjust my rear struts because the mount has the piston rod too far into the trunk so the key wont fit to adjust them.

THis bothers me alot, Im going to be runnning D Specs with these and Id like to be able to adjust them........

can someone hook me up with the dimensions like they did for the tein basics. I am sending these off tomorrow to be cut.


M

http://www.overkillengineeringmotorsports.com/

I need to see some pics of the tokico's so that I can see what you are talking about.

M

http://www.overkillengineeringmotorsports.com/

Can I get a list of people that would be interested with your shocks next to your name??

M

http://www.overkillengineeringmotorsports.com/

1.. EVOFIRE ******Gravana's*******

AGX's here.



PRND321 Till I DIE
Old Motor: 160whp & 152ft/lbs, 1/4 Mile 15.4 @88.2
M45 + LD9 + 4T40-E, GO GO GO

PLease add your self to the list. I will need the ID and OD of the spring that you have and the threaded shaft diameter. Thanks.

M

http://www.overkillengineeringmotorsports.com/

u need id and od from everyone...or just those that you dont have?

I have the gravans, so for the others, I dont know what the difference are, or if there even are?

M

http://www.overkillengineeringmotorsports.com/

HMMM interesting


HOLY HELL ITS BACK!!!

In Loving Memory of Phil Martin December 14 2005
Alexis: Dustin, you're ghey, lol. I am better. I have tits, and tits rule all.

1.. EVOFIRE ******Gravana's*******
2) notec - Tein Basics (2.5" springs, same as all coilovers pretty much))




Built 94-97 head for sale: http://www.j-body.org/classifieds/engine/47069/

1. EVOFire - Gravanas
2. notec - Tein Basics
3. J TO ENVY - Eibach Pro Kit springs / KYB AGXs

1. EVOFire - Gravanas
2. notec - Tein Basics
3. J TO ENVY - Eibach Pro Kit springs / KYB AGXs

@ FAST2.4 P: Are you going to be making front and rear mounts or just rear mounts?

1. EVOFire - Gravanas
2. notec - Tein Basics
3. J TO ENVY - Eibach Pro Kit springs / KYB AGXs
4. Kardain - Eibach Pro Kit springs / KYB AGXs


I can get the shaft measurement easily, but not the springs w/out dismantling the suspension again but should be the same ID as stock.

both front and rear. I am doing the rear first as i see this as more of a problem. Good to see the list growing. How many people out of the 26 from the other GB did not get anything??

Mark

http://www.overkillengineeringmotorsports.com/

FAST2.4 P wrote:both front and rear. I am doing the rear first as i see this as more of a problem. Good to see the list growing. How many people out of the 26 from the other GB did not get anything??

Mark

The HT GB never came to be




Built 94-97 head for sale: http://www.j-body.org/classifieds/engine/47069/

1. EVOFire - Gravanas
2. notec - Tein Basics
3. J TO ENVY - Eibach Pro Kit springs / KYB AGXs
4. Kardain - Eibach Pro Kit springs / KYB AGXs
5.JMHZ2401- Eibach Sportlines/ Koni reds



FU Tuning

Perfect. If I can get 10 that would be awesome.

http://www.overkillengineeringmotorsports.com/

FAST2.4 P wrote:Perfect. If I can get 10 that would be awesome.

as soon as you can get pics up, and pricing, i can get atleast 2-3 more from deserttuners.com. i have the thread posted there, but they wont list it in their GP forum until pics and prices are up