stock injectors - Nitrous Oxide Forum

Forum Post / Reply
You must log in before you can post or reply to messages.
stock injectors
Saturday, January 08, 2005 9:15 PM
whats the size of the injectors in a 2.4?


i see after market injectors for the 2.4 that are 270 cc, 320 cc, and 550 cc. i was thinknig of getting a set this year <br>


Im a Xbox 360 fanboy...and damn proud of it!!

Re: stock injectors
Sunday, January 09, 2005 12:18 PM
I think they are 24lb/hr, which roughly translates to 250cc.

<br>


4cyltuner.com - Information Source For 4 Cylinder Tuners
Buy stuff from CarCustoms Ebay! Won't be disappointed!

Re: stock injectors
Tuesday, January 11, 2005 3:40 PM
yea ive heard 240-260, nice thing is with a 2.4 you can use the injectors from the GM supercharger kit they are 310cc, im sure if you search around enough on them you can find the part # for them they are a direct swap, they might dump a little heavy without the juice so you prob need to get an apexi safc to trim some fuel and get it right <br>


1989 Turbo Trans Am #82, 2007 Cobalt SS G85





Re: stock injectors
Tuesday, February 01, 2005 4:19 PM
I believe the low impedance from 95 to 99 are 24lb and the newer ones are 190lb high impedance. I was using the injectors out of a 2.3 H.O which are 310cc on my 2200 than it was running a little rough than I switched to the 2.3 L.O injectors (210cc) and it runs fine without turning down the pressure.
Re: stock injectors
Tuesday, February 01, 2005 4:21 PM
Sheng Kai wrote:I believe the low impedance from 95 to 99 are 24lb and the newer ones are 190lb high impedance. I was using the injectors out of a 2.3 H.O which are 310cc on my 2200 than it was running a little rough than I switched to the 2.3 L.O injectors (210cc) and it runs fine without turning down the pressure.


190 lbs?

I hope that is a typo. The injectors are the same size from 95-99 and 00-02.





4cyltuner.com - Information Source For 4 Cylinder Tuners
Buy stuff from CarCustoms Ebay! Won't be disappointed!

Re: stock injectors
Tuesday, February 01, 2005 5:10 PM
Sorry I meant 190 cc and I was pretty sure that when the switched to the high impedance they made them 190cc. Also I can be wrong about this.
Re: stock injectors
Monday, February 14, 2005 10:01 PM
what is the lb rating on the 2200 stock injectors?
Re: stock injectors
Tuesday, February 15, 2005 6:21 AM
2200 ohv have 19 lb/hr stock injectors.

yes, shifted. the 2.4 are 24 lb/hr. both engines also have high impedance.



Re: stock injectors
Tuesday, February 15, 2005 6:17 PM
I 'm getting ready to put a set of 2.4 injectors into my 96 2.2 with a S-AFC II controlling them on a custom top feed conversion. We'll see what happens. Should be done by the end of March.
Re: stock injectors
Tuesday, February 15, 2005 6:30 PM
so how would the 24# injectors out of a 97 lt1 act alright in the 99 2200?
Re: stock injectors
Wednesday, February 16, 2005 7:51 AM
if they fit the rail and harness, they would act similar




Re: stock injectors
Wednesday, February 16, 2005 7:52 AM
damnit we need an edit/delete button. i meant they would act like 2.4L injectors. same flow rate. would have to have some fuel trimmed off probly to make it idle right.



Re: stock injectors
Wednesday, February 16, 2005 7:02 PM
JB wrote:2200 ohv have 19 lb/hr stock injectors.

yes, shifted. the 2.4 are 24 lb/hr. both engines also have high impedance.


Nope, 96-98 are all low impedance, 99 has both, 00 and up are are all high impedance.






4cyltuner.com - Information Source For 4 Cylinder Tuners
Buy stuff from CarCustoms Ebay! Won't be disappointed!

Re: stock injectors
Thursday, February 17, 2005 9:33 AM
yea. i meant to say 00+ are high impedance. just left that part out. thanks



Re: stock injectors
Thursday, February 17, 2005 9:21 PM
how can you tell the difference between high impedence and low impedence? I have a 99 model engine and trans in my 97 rs.
Re: stock injectors
Friday, February 18, 2005 7:40 AM
measure the resistance across the injector plug with an ohm meter/multimeter. high impedance will be around 12-14 ohms.



Re: stock injectors
Saturday, February 19, 2005 9:40 PM
JB wrote:measure the resistance across the injector plug with an ohm meter/multimeter. high impedance will be around 12-14 ohms.



this may be a stupid question, but i should measure across the terminals on the actual injector?
Re: stock injectors
Saturday, February 19, 2005 10:48 PM
Yes, as long as you unplug the clip first.





4cyltuner.com - Information Source For 4 Cylinder Tuners
Buy stuff from CarCustoms Ebay! Won't be disappointed!

Re: stock injectors
Monday, February 21, 2005 8:28 AM
The high impedance (skinny injectors) used in some 99's and all of the 00+ 2.4L's are different flow rates. I had my high impedance injectors sent to RC Engineering for balancing and they were around 190cc if I remember correctly. In fact, they have been even lower. I think the 95-98 were between 240-260 cc.

Mark P.
Re: stock injectors
Monday, February 21, 2005 3:23 PM
is there any advantage to putthe 22 or 24 # injectors on a bolt on 2200? I have access to both. Just curious as if it is worth the time. i will be spraying soon also. If at all i will put the bigger injectors in for that.


ryan
Re: stock injectors
Tuesday, February 22, 2005 6:43 AM
Mark Pain wrote:The high impedance (skinny injectors) used in some 99's and all of the 00+ 2.4L's are different flow rates. I had my high impedance injectors sent to RC Engineering for balancing and they were around 190cc if I remember correctly. In fact, they have been even lower. I think the 95-98 were between 240-260 cc.

Mark P.


This is what I believe to be correct as well, the 99+ high impedance injectors don't flow as much as the earlier ones.


15.3 @ 89.97mph, 14's on the way?

For Sale:
'01 SFGT springs $50CAN
Fidenza Flywheel '00-'02 2.4 (getrag) $300CAN
Getrag '00-'02 2.4 8000kms $800

Forum Post / Reply
You must log in before you can post or reply to messages.

 

Start New Topic Advanced Search