you sure the fuel pump was going, and its not your tune??
it was the fuel pump, i got a pressure gauge and it was dropping, got a new pump in last night. and due to the fact i have to work i will not be going to the dyno till later today
fully built 2200-TO4E T3/T4-HP tuners-373hp @18psi
its later today...
Fall 08 Omaha/western Iowa area meet...
CLICK ME!
Damn it I read all of this and got nothing....like watching a porno and when the good part comes the power goes out....um I mean.....video where is it?
____________________________________
Primer Counts as Custom Paint Right?
BTW: This is my Sig.
its later.................. the next day!
It takes 8,460 bolts to assemble an automobile, and one nut to scatter it all over the road
news is- did the pull
bad news, i am editing the video and stuff. that way you can see the setup then the dyno run. tomorrow grasshoppa's
fully built 2200-TO4E T3/T4-HP tuners-373hp @18psi
what numbers?
DRIVE HARD OR DONT DRIVE AT ALL!!!
361@6000 and 345@3500 18 psi with a 50 hit. then 310 and 327 with no bottle. i have to go pick up the sheet later
fully built 2200-TO4E T3/T4-HP tuners-373hp @18psi
Very nice numbers for an LN2. Which trim T04E are you running, compressor and exhaust side?
I have a hard time believe, in my experience with nitrous, that you only gained 18ft/lbs or torque with a 50shot..... every car I have ever seen using nitrous gives a considerablly larger increase in torque over horsepower. I do believe that you gained 51hp, but i would have believe you more if you had said 60-65ft.lbs of toruqe not 18. that sounds off to me. Maybe it's different because you have a turbo'd 4 banger and they react differently to nitrous... who knows, but it is the exact opposite of what I normally see out of nitrous gains.
On the other hand....you have other fingers.
In my family we teach that boys have a God-stick and girls have a Shame Cave. -John Stewart
the nitrous dont kick in till after the tourqe curve started dropping, i fugged up oin hittin the switch
turbo specs
40-trim
.63a/r
2 1/2 inch swing vavle
and due to the fact that my grandpa is in poor health and is more then likely on his last leg i am heading back for washington.
so video editing is at a stand still, i will post up what i have later though
fully built 2200-TO4E T3/T4-HP tuners-373hp @18psi
A week of tuning and you lost 63whp?
- 93 mph in the 1/8 mile
Member of J-Body Of Michigan.
i still dont have the tune just perfect yet. and i dont have a hole lot of juice left
fully built 2200-TO4E T3/T4-HP tuners-373hp @18psi
Then why don't you wait and post when you
FINALLY have video and stuff
i post to let people know why i dont have videos up yet so my ass dont get flamed again.
tomorrow for sure, i have a wedding to go to
fully built 2200-TO4E T3/T4-HP tuners-373hp @18psi
Truck brake problems, grandfather in poor health, wedding, need more time to edit video, have to pick the sheet up later, fuel pump issues, tune isn't spot on, hit the n2o too late(even though if you did it right, it would be on a window switch and wot sensor so you wouldn't have to hit a button like a ricer in a street race), all this just seems like the bad things are happening conveniently at the wrong(or right) time. If I do a dyno run, the slip is printed right then and there, so that excuse was hilarious "have to pick up the sheet later".... but I wish the best for your grandfather(because if that is a lie and BS excuse, I hope you rot in hell). and hope all gets fixed with the pickup.... but seriously, ALLL of this @!#$, even if it is all legit, is holding you from getting us any ounce of proof.... It just all seems to convenient to me. Oh and "Tomorrow for sure" was written yesturday, or technically 2 days ago as it is now 2:00 Sunday morning.... give me a @!#$ break.
On the other hand....you have other fingers.
In my family we teach that boys have a God-stick and girls have a Shame Cave. -John Stewart
^^^^^
bro i got alot of @!#$ up @!#$ going on in my life right now. my least worry is getting a vid put up here.
1. my grandpa was exposed to radition when he was younger to remove the warts from his hands. he has a tumor and his brain stem
2. being as i just moved to montana and i am now moving back i have alot of packign and thinking to do,
3. i have a fiance 1000 miles away right now that i like to spend alot of time talking too.
i am sorry i cant spend countless hours in front of the computer to get this done.
it will come, i PROMISE. and if you have ever grown up in a small town you dont break a promise
and dont @!#$ doubt me bro. makes me a little edgy
fully built 2200-TO4E T3/T4-HP tuners-373hp @18psi
KavyKidLN2 wrote:and dont @!#$ doubt me bro. makes me a little edgy
E-thuggin FTL
It's funny that you can't spend countless hours in front of the computer but you can reply rather quickly when someone posts in your thread. If this is all
, just admit it and get it over with. If not, don't post until you have actual proof.
KavyKidLN2 wrote:^^^^^
bro i got alot of @!#$ up @!#$ going on in my life right now. my least worry is getting a vid put up here.
1. my grandpa was exposed to radition when he was younger to remove the warts from his hands. he has a tumor and his brain stem
2. being as i just moved to montana and i am now moving back i have alot of packign and thinking to do,
3. i have a fiance 1000 miles away right now that i like to spend alot of time talking too.
i am sorry i cant spend countless hours in front of the computer to get this done.
it will come, i PROMISE. and if you have ever grown up in a small town you dont break a promise
and dont @!#$ doubt me bro. makes me a little edgy
No need to get edgy. Just put yourself in our shoes. Everyone that has posted in here has either posted graphs, videos, pictures of their car on the dyno, or had numerous people there to back up their claims or any combination of the above listed.
You have posted a graph marked camaro.
FORGET GIRLS GONE WILD WE HAVE GOVERNMENT SPENDING GONE WILD!
whats next? a vid of the camaro on the dyno but its really your car, just photoshopped?
here's a list of excuses you can choose from:
my throttle pedal leg got broke
my dog ate my dynosheet
kinko's was closed so i couldn't scan my dynosheet
aliens attacked and my car was blown up
countless hours on the internet? eh.. no. it takes about an hour to do a dyno pull, 10-20 mins to load up the vid and scan the sheet, another 10 or so mins to load the vid and scan to photobucket and 30 freaking seconds to post.
Fall 08 Omaha/western Iowa area meet...
CLICK ME!
Zach, if you need a hand with the vid editing, give me a holler once you've moved back this way. I'll do the editing and post the vid.
So, since he kinda broke the truck, the original plan didn't quite work out
How about one picture of your engine and turbo set up?
Edited 1 time(s). Last edited Monday, September 15, 2008 1:45 AM