Look what I found, 14 sec ECOtec, Whats up
-Ben
ONLY All Motor Quick 8 H2 (GMSCB 2005)
Best times of 2005
60' - 1.955 (9/30/05)
330' - 5.987 (9/30/05)
1/8 - 9.312 (9/30/05)
M.P.H.- 74.85 (9/30/05)
1000' - 12.213 (9/30/05)
1/4 - 14.670 (9/30/05)
M.P.H.- 92.78 (9/30/05)
hahaha, next time i get to the track ben, i'll be right there with you
Yea, that would be awesome
your all most there
ONLY All Motor Quick 8 H2 (GMSCB 2005)
Best times of 2005
60' - 1.955 (9/30/05)
330' - 5.987 (9/30/05)
1/8 - 9.312 (9/30/05)
M.P.H.- 74.85 (9/30/05)
1000' - 12.213 (9/30/05)
1/4 - 14.670 (9/30/05)
M.P.H.- 92.78 (9/30/05)
What happend to this post? its the same idea
-Ben
ONLY All Motor Quick 8 H2 (GMSCB 2005)
Best times of 2005
60' - 1.955 (9/30/05)
330' - 5.987 (9/30/05)
1/8 - 9.312 (9/30/05)
M.P.H.- 74.85 (9/30/05)
1000' - 12.213 (9/30/05)
1/4 - 14.670 (9/30/05)
M.P.H.- 92.78 (9/30/05)
Remember when 14 sec was hard? i dug this one up from the grave, just for a jog down memory lane
Im sure i was the first to break the 14 sec zone? and best of 15.004 at the bash in 2005
See ya at the bash in 2007
-Ben
Overall Best times
60' - 1.857* (6/24/07)-(Drag Radials 205-50-15)
330' - 5.552* (6/24/07)
1/8 - 8.702* (6/24/07)
M.P.H.- 79.49 (6/17/07)
1000' - 11.388* (6/24/07)
1/4 - 13.671* (6/24/07)
M.P.H.- 100.79* (6/17/07)
Great Lakes Dragaway (6/24/07 Import Wars #3)
* - First run on the day set NEW all motor record
next run backed up record by 1% (slip in profile)
** ALL MOTOR **
* 160.9whp @ 6394rpm *
Website: www.benwenzeljr.com
HPT is to thank
which i need badly
and noone close to tune me
The one, the only, ME.
2465 lbs without me
141 hp @ 6300 (ran out of rpms)
123 ft lbs @ 5200
running lean stock ECU
This goes to prove we are actually advancing.
I would like to see some more people play with higher compression. Ben, what octane do you have to run for that 12.5:1?
2004 Cavalier. Razzi. (Sold)
1998 Corvette. Some mods.
1992 Typhoon. Lots of mods.
1994 Civic VX 44MPG
well heres what i did for now:
was running punp 87 with the 8:9:1 pistons. After i installed the 12.5:1 added about 8 gallons of 93 into the tank, so that was about 5 gal 87 and 8 gal 93, went to the dyno for break in, then we poured it on, maybe it was the rings seating better cuz on one of the high 170 pulls the factory computer started pulling back timing cuz of knock, so Don and Adam decided to pull back some timing and pulled it again, so i ended the day in the mid 170's. Friday the 13th got some Sonoco 100 unleaded and going to the dyno on Sat the 14th. The higher gas and added timing with adjustable cam gears lookin for the 200 whp mark
. Thanks for the question, will keep you posted
-Ben
Overall Best times
60' - 1.857* (6/24/07)-(Drag Radials 205-50-15)
330' - 5.552* (6/24/07)
1/8 - 8.702* (6/24/07)
M.P.H.- 79.49 (6/17/07)
1000' - 11.388* (6/24/07)
1/4 - 13.671* (6/24/07)
M.P.H.- 100.79* (6/17/07)
Great Lakes Dragaway (6/24/07 Import Wars #3)
* - First run on the day set NEW all motor record
next run backed up record by 1% (slip in profile)
** ALL MOTOR **
* 181whp @ 7600rpm *
Website: www.benwenzeljr.com
I'd like to see a 11.5-12:1 CR that was setup for 91 octane. Definately keep us posted on how your setup turns out.
2004 Cavalier. Razzi. (Sold)
1998 Corvette. Some mods.
1992 Typhoon. Lots of mods.
1994 Civic VX 44MPG
Like everyone knows that with higher compression yeilds higher octaine. I know for sure my setup will not run anything less than 100. Maybe you could get away with it with factory compression.
Thats all for now
-Ben
Overall Best times
60' - 1.857 (6/24/07)-(Drag Radials 205-50-15)
330' - 5.552 (6/24/07)-(Drag Radials 205-50-15)
1/8 - 8.690 (7/22/07)-(Conquesrt Radials 195-70-14)
M.P.H. - 81.87 (7/22/07)-(Conquest Radials 195-79-14)
1000' - 11.274 (7/22/07)-(Conquest Radials 195-70-14)
1/4 - 13.442 (7/22/07)-(Conquest Radials 195-70-14)
M.P.H. - 104.08 (7/22/07)-(Conquest Radials 195-70-14)
** ALL MOTOR **
* 181whp @ 7600rpm *
Website: www.benwenzeljr.com
2007 GM Tuner Bash Runner Up - Broken Pressure Plate
#1 Qualifer 13.857 @ 101.49
