Universal aem ems 4 - Tuning Forum

Forum Post / Reply
You must log in before you can post or reply to messages.
Universal aem ems 4
Sunday, July 01, 2012 8:10 AM
Hey every one I'm
In the process of looking for a tuning devise for my needs,
Hptuners is not a option anymore,

It's to limited to my set up and I want more boost,
Does any one have wired a universal aem or haltech or any stand alon that could shine some lite my way on diagrams of the stock harness and stuff.

Re: Universal aem ems 4
Friday, July 06, 2012 3:26 PM
i wired a Haltech in as a standalone it all depends on what you want the standalone to run your biggest problem you are going to run into is finding a standalone that can interpret the 6+1 trigger on your crank assuming you have an ecotec. Also if you want any help on here you might want to stop being lazy and fill out your profile


RIP Cpl Derek Kerns And Cpl Robby Reyes
24th MEU VMM-261 (REIN) V22 Crewchiefs
11 April 2012 Morocco (African Lion)
Re: Universal aem ems 4
Sunday, July 08, 2012 7:48 AM
MillerBilt Racing wrote:

finding a standalone that can interpret the 6+1 trigger on your crank assuming you have an ecotec



No need.

I have a bunch of crank signal converters that splice directly into the Ecotec Sensor. Tested on an oscilliscope. Perfect. Tested on an SDS system. Perfect.

No need for magnets, no need for additional trigger wheels and fabrication.



Re: Universal aem ems 4
Sunday, July 08, 2012 5:02 PM
Erik Nyman wrote:

MillerBilt Racing wrote:

finding a standalone that can interpret the 6+1 trigger on your crank assuming you have an ecotec



No need.

I have a bunch of crank signal converters that splice directly into the Ecotec Sensor. Tested on an oscilliscope. Perfect. Tested on an SDS system. Perfect.

No need for magnets, no need for additional trigger wheels and fabrication.


I didnt need to do that either im still using an internal trigger wheel (58x) but my engine is a built LSJ in my sunfire


RIP Cpl Derek Kerns And Cpl Robby Reyes
24th MEU VMM-261 (REIN) V22 Crewchiefs
11 April 2012 Morocco (African Lion)
Re: Universal aem ems 4
Wednesday, August 01, 2012 9:38 AM
btw the new MSextra firmware supports the GM7x wheel.



I roll on steelies. Work-in-progress daily-sleeper potential.
http://www.j-body.org/classifieds/engine/60493/
Re: Universal aem ems 4
Wednesday, December 10, 2014 5:57 PM
I need a trigger wheel for a 04 cavalier to by pass the 07 colbalt trigger

I would like to buy a 6+1 trigger wheel for the 04 cavalier 2.2 ecotec

Re: Universal aem ems 4
Tuesday, September 29, 2015 6:25 PM
I am looking to buy a Haltech standalone system. Until I read this post, I thought I just need to get it and tune. This whole crank trigger wheel has got me confused. Can I wire my standalone in without any issues on my L61 ecotec?


"FRIENDS DON'T LET FRIENDS DRIVE STOCK"




Re: Universal aem ems 4
Wednesday, September 30, 2015 4:05 AM
You need a newer style trigger wheel last I knew.





Re: Universal aem ems 4
Friday, October 02, 2015 1:41 PM
This is from Tinkles to me on another post.

"If you run a standalone ECU then you will not need a trigger wheel. The trigger wheel is just to run other engines on the stock ECU. Any decent standalone will allow you to program in the engine's stock "trigger wheel".





"FRIENDS DON'T LET FRIENDS DRIVE STOCK"




Forum Post / Reply
You must log in before you can post or reply to messages.

 

Start New Topic Advanced Search