Coming soon... - Page 6 - Tuning Forum

Forum Post / Reply
You must log in before you can post or reply to messages.
Re: Coming soon...
Monday, August 13, 2007 10:56 AM
listening


-Trailblazer SS - not so custom 6.0L - custom intake - custom tune
- (1) 2.4L on an engine stand (1) blown trans (2) good quad trans (1) eco trans = party


Re: Coming soon...
Monday, August 13, 2007 11:27 AM
Luis Marroquin wrote:

hey shifted any new breakthroughs?


I've got the power supply designed up, I'm waiting on yet some more parts from Mouser before I can actually start writing code. Unfortunately I can't do much work on them without buying a decent JTAG interface, but luckily my work will be purchasing two such $4,500.00 JTAG interfaces, one of which I will be using on this project. This weekend I did a lot of work on design, and I'm getting ready to send the schematics to a board manufacturer as soon as I can get them finalized.

Things are moving along nicely, at about the rate I had hoped they'd move, so I'm still on schedule.





4cyltuner.com - Information Source For 4 Cylinder Tuners
Buy stuff from CarCustoms Ebay! Won't be disappointed!

Re: Coming soon...
Monday, August 13, 2007 11:33 AM
which JTAG did you go with?

it is damn expensive, but test plan generation keeps R&D time down.


Desert Tuners

“When you come across a big kettle of crazy, it’s best not to stir it.”


Re: Coming soon...
Monday, August 13, 2007 12:18 PM
Keil RealView





4cyltuner.com - Information Source For 4 Cylinder Tuners
Buy stuff from CarCustoms Ebay! Won't be disappointed!

Re: Coming soon...
Monday, August 13, 2007 3:24 PM
I'll have to check it out. we use Corelis here.


Desert Tuners

“When you come across a big kettle of crazy, it’s best not to stir it.”


Re: Coming soon...
Tuesday, August 14, 2007 1:56 AM
looking good!!! Wish I had the know-how and brains to do this stuff




SPD RCR Z - '02 Z24 420whp
SLO GOAT - '04 GTO 305whp
RACER X - '78 Opel Kadett W41 Swap

Re: Coming soon...
Tuesday, August 28, 2007 8:45 PM
How is it coming along? I'm quite interested in the progress on this. I'm in the middle of gathering parts for my car here and there and would like tuning thats not limited by 7000rpm.


--------------------------------------
04 Cavalier LS Sport SE- Red with factory silver stripes.
16.186 @ 86.98mph
Re: Coming soon...
Wednesday, August 29, 2007 4:51 AM
I'm still working on it, its comin along, just slow these past two weeks because of long days at work.





4cyltuner.com - Information Source For 4 Cylinder Tuners
Buy stuff from CarCustoms Ebay! Won't be disappointed!

Re: Coming soon...
Wednesday, August 29, 2007 7:22 AM
Atleast there is progress, I cant wait to see the finished product.


--------------------------------------
04 Cavalier LS Sport SE- Red with factory silver stripes.
16.186 @ 86.98mph
Re: Coming soon...
Wednesday, August 29, 2007 9:23 AM
Whats is the price tag on one of these?



Re: Coming soon...
Wednesday, August 29, 2007 9:31 AM
^ Don't know yet





4cyltuner.com - Information Source For 4 Cylinder Tuners
Buy stuff from CarCustoms Ebay! Won't be disappointed!


Re: Coming soon...
Wednesday, August 29, 2007 1:30 PM
I cant wait to rewire my car Ron

You coming up to WI to help do so?



Re: Coming soon...
Saturday, September 01, 2007 9:02 AM
Hey shifted, i see you were looking for someone to manufature the boards. I can take care of that part for you. I have autocad software for board designs, and a manufacture that will do them at very good rates. As long as you can supply a full schematic of what you want, and any physical constraints, L x W , I can do the rest.



M90'd Built LGO-15 PSI
http://webstarts.com/quadper4mance
Re: Coming soon...
Saturday, September 01, 2007 9:07 AM
Here is a screen shot of a small board i recently did, this is a knock sensor decoding circuit, it will take the knock sensors signal, process and digitize it, and flash a dash mounted LED when knock is detected. it will also serve as an input to the megasquirt to datalog knock ativity.





M90'd Built LGO-15 PSI
http://webstarts.com/quadper4mance
Re: Coming soon...
Saturday, September 01, 2007 9:17 AM
^ I'll be in touch with you. There are actually 4 boards in this unit, processor mainboard, fuel, spark, and power.





4cyltuner.com - Information Source For 4 Cylinder Tuners
Buy stuff from CarCustoms Ebay! Won't be disappointed!

Re: Coming soon...
Saturday, September 01, 2007 10:58 AM
okay, that will work.
also, the software can do multiplain boards, and SMD components. they cannot be order with parts installed, either you or i would have to do that. I do not have the equipment to solder SMD components, but i can do standard discrete components. thats if your also looking for someone to assemble.



M90'd Built LGO-15 PSI
http://webstarts.com/quadper4mance
Re: Coming soon...
Saturday, September 01, 2007 11:07 AM
The processor is the only smd part so far. I'm trying to find a socket for it, but as it stands, that would add more than $75 to the cost of the board. I'm talking with Schmartboard to do the actual production, because they can add reflow solder pads for the SMD components. They can do board design, but its an added cost. What program are you using for design?





4cyltuner.com - Information Source For 4 Cylinder Tuners
Buy stuff from CarCustoms Ebay! Won't be disappointed!

Re: Coming soon...
Saturday, September 01, 2007 12:21 PM
www.pad2pad.com

i like it becuase it has an automatic trace routing function. you place all the components on the board, tell it what components are suppose to be hooked to each other, and it auto generates the traces on the board.



M90'd Built LGO-15 PSI
http://webstarts.com/quadper4mance
Re: Coming soon...
Sunday, September 02, 2007 8:21 AM
MAKE ONE FOR THE GTZ!......


Great work man!

Shaun, are you puting that on our 95 GA?

Chris


'02 Z-24 Supercharged
13.7 @102.45 MPH Third Place, 2007 GMSC Bash SOLD AS OF 01MAR08

Re: Coming soon...
Sunday, September 02, 2007 9:28 AM
nope, but i thought i could help if needed. im pretty content with the plain 'ol ms.



M90'd Built LGO-15 PSI
http://webstarts.com/quadper4mance
Re: Coming soon...
Monday, September 03, 2007 12:25 AM
Shaun, PM'ed

Re: Coming soon...
Sunday, September 09, 2007 7:56 PM
everytime i hop on j-body this is the first thread i go to, just thought id throw that out there. Shifted, anything new?





Re: Coming soon...
Sunday, September 09, 2007 7:59 PM
Been SUPER busy at work the past week, and now I have to go to Japan, so not much new this week or next.





4cyltuner.com - Information Source For 4 Cylinder Tuners
Buy stuff from CarCustoms Ebay! Won't be disappointed!

Re: Coming soon...
Monday, September 10, 2007 11:55 AM
go visit the Marine's!

have fun at LA X ..LOL

Chris


'02 Z-24 Supercharged
13.7 @102.45 MPH Third Place, 2007 GMSC Bash SOLD AS OF 01MAR08

Re: Coming soon...
Wednesday, September 12, 2007 7:27 AM
Most of us Marines are elsewhere at the moment, if ya missed the memo... JK man, def go to see them, Okinawa is nice this time of year
BTW Ron you man not remember me but I had contacted you back in 05 when i first looked into boost, and now with my 2nd deployment out of the way the cash is in to do my swao, couldn't have done it without your info!



Edited 1 time(s). Last edited Wednesday, September 12, 2007 7:32 AM


Forum Post / Reply
You must log in before you can post or reply to messages.

 

Start New Topic Advanced Search