Emanage Problems: Car won't START - Tuning Forum

Forum Post / Reply
You must log in before you can post or reply to messages.
Emanage Problems: Car won't START
Sunday, May 08, 2005 11:41 AM
I installed the Emanage last night but the car won't start. When I put the key in the ignition everything works like normal but when I try to start the car i hear a click noise and all the power goes away. I can't figure out what i did wrong all the wires are soldered together. i did have to extend the wire about 2 feet, I also folled the wiring diragram that was on Jason's webpage. I thing it may be a jumper setting problem, I left the unit like it came but I noticed on Jason's webpage it said Ignition input pull down and Ignition output 5V. Any help would be appreciated.






Re: Emanage Problems: Car won't START
Sunday, May 08, 2005 12:19 PM
your ignition wires are backwards with the in and out its opposite of what you think it would be i ran in to the exact same problem




Re: Emanage Problems: Car won't START
Sunday, May 08, 2005 1:16 PM
or your battery is dead.



Re: Emanage Problems: Car won't START
Sunday, May 08, 2005 1:22 PM
OrangeZ, I switched the wires around and it's still doing the same thing.

Cold Fusion, I have tested the battery and it is not dead.

Also, after I try to start the car it takes a couple of min for the power to come back





Re: Emanage Problems: Car won't START
Sunday, May 08, 2005 2:01 PM
put the ign wires back to normal and see if the car starts, if not then your problem may lie somewhere else

let us know how you make out




Re: Emanage Problems: Car won't START
Sunday, May 08, 2005 3:57 PM
I have tried reconnecting the ignition wires and nothing, i'm going to put everything back to stock to make sure I didn't fry my PCM.

On this page when it says ignition input pull down and output voltage 5Volts what does this mean. Could this be my problem.



Re: Emanage Problems: Car won't START
Sunday, May 08, 2005 4:13 PM
Definitely the problem. Here:

Jumper settings inside the E-manage:

JP1 Ignition input pullup/pulldown select
1-2 A resistor is pulled down to ground
2-3 A resistor is pulled up the +ve rail
* Use 1-2 when the ECU's driver transistor is
connected to ground
* Use 2-3 when the ECU's driver transistor is
connected to +ve (5V or 12V will determine JP2's
setting)
Supposedly you can see the input voltage in the Main Unit Setting
Information window. If it's 0v, use 1-2. If it's 5v or more, use 2-3.

JP2 Ignition output select
1-2 Output resistor connected to +5V
2-3 Output resistor connected to +12V
* This will depend on the ECU ignitor signals output
* JP2 enables the e-manage to duplicate the amplitude
of the original signal

JP3 airflow/VTEC output select
1-2 2nd airflow meter
2-3 VTEC
* Even if you don't have a 2nd airflow meter, leave it on 1-2 for non-
VTEC applications

JP4 airflow/VTEC input select
1-2 VTEC
2-3 2nd airflow meter
* Even if you don't have a 2nd airflow meter, leave it on 2-3 for non-
VTEC applications
* On 1-2, enables pulldown resistor (for use as VTM signal). This is
required because the VTM output is inverted with the VTEC out.

JP5/JP6 Sub injector drivers
Jumper off - Disabled
1-2 - Enabled
* Only enable if you're going to control extra injectors with the E-
manage

JP7 VTEC
1-2 Non-VTEC
Jumper off - VTEC
* On 1-2, enables pullup resistor (for use as MAF output)




<a href="http://www.j-body.org/members/mrpute"><img src="http://www.j-bom.com/images/sigs/putesig.jpg">
Re: Emanage Problems: Car won't START
Sunday, May 08, 2005 5:42 PM
Well, I'm pretty sure I just shorted out my PCM. When I put the key in the ignition I get the chime but when I turn the key to the on position the lights dim and when I try to start nothing . I thought I had drained my battery somehow and tried to get a jump but the same thing happens. Guess I should find a new PCM and start over.





Re: Emanage Problems: Car won't START
Sunday, May 08, 2005 6:21 PM
I think that before you conclude that, you check EVERYTHING over.


<a href="http://www.j-body.org/members/mrpute"><img src="http://www.j-bom.com/images/sigs/putesig.jpg">
Re: Emanage Problems: Car won't START
Monday, May 09, 2005 4:38 AM
For JP1 and JP2 aren't these the factory settings





Re: Emanage Problems: Car won't START
Monday, May 09, 2005 10:53 AM
I've checked the wiring and swapped ina new battery and the same thing keeps happening. I don't know what could be causing this, if you guys have any ideas I'm willing to try anything right now.






Re: Emanage Problems: Car won't START
Tuesday, May 10, 2005 1:42 PM
well I found out that the car was in theft mode. Did anyone have this problem installing their emanage?




Forum Post / Reply
You must log in before you can post or reply to messages.

 

Start New Topic Advanced Search