I'm looking for a set of 4 34-36lbs/hr 2A/0.5Ohm injectors.
I know the ford brown tops are low impedence and 36lbs/hr but I don't know to buy them.
Rc injectors are too expensive.
Gilles
2.3 Ho
Thank you Rod. That's the site I was looking for to get stock replacement,
It doesn't say what's the size of the injectors so I got some homework to do unless you know the number for the brown top.
Thanks again Rod.
Gilles
2.3 Ho
I think the cobalt ss injectors are 36 lbs
yeah but they are high impedence.
I need a set of low impedence.
Gilles
2.3 Ho
I'm out on that one my friend.
I think the best thing would to send them an e-mail directly or find out the casting number from a ford catalog. Otherwise. I'm out on this one.
you can buy a set of stock injectors for an '05 Cobalt SS S/C injectors.
they are for sale as I have new injectors that came with the GM Stage 2 kit for my car. 15,000miles on them.
[FONT="Arial Black"][SIZE="4"] Click to see My CARDOMAIN Page
[FONT="Arial Black"][SIZE="1"][COLOR="Red"]1/4 - 13.9 @ 101.6, Best 60ft 2.1840 Performance mods to obtain best times - GMS2 and a K&N drop in filter.
But now GMS2 is SOLD [SIZE="2"]
Car needs more work with tune. 13.9 with very rough tune.
[SIZE="4"][FONT="Arial Black"][COLOR="Blue"]GIMILI Drag Raceway September 29th or BUST
i got some accels off summit racing
1989 Turbo Trans Am #82, 2007 Cobalt SS G85
I have Accels in my car and have had 0 issues. I am going to be switching to RCEs for 07 though. Just a business deal though....nothing about the quality is causing me to switch at all.
Let me know if you need some Accels. I usually get them at a good price. Same with the RCEs.
I used to race cars, now I race myself.
5K PB: 24:50
10K PB: 54:26
you can use grand prix gtp 3800 injectors they are 36lbs
hey Gilles, did you find part number?
i'm also wondering where to find brown tops
thanx
I have a set of Stock Colbalt SS s/c 36lb injectors for sale. CHEAP!!!
yeah, but these are high impodance, and i need low as i have a 97!!!
Quote:
I'm looking for a set of 4 34-36lbs/hr 2A/0.5Ohm injectors.
Won't find 'em.
Don't exist.
Can't be bought.
Can't even be made.
.5 ( or 1/2) Ohm injector draws 24 amps of current on a 12 volt system.
Current = voltage divided by resistance. 12 divided by .5 = 24. A 2A injector will be about 6-8 Ohms.
If your pcm is able to drive low impedance injectors then it will also drive high impedance injectors. The voltage corrections in software might not match but most people here don't seem to care about that anyway.
-->Slow
It was a mistake. it's 2ohm 0.5Amp¸
I got a set of brown top on Ebay.
Merlin - There's a bunch of part number for the brown top. The one I got are E5ZE A3B IIRC. I gotta check. They came from an XR4TI. Give me a week and they will most likely be yours if you want them. I only need them for testing. I want to see if the injectors I have now work fine or not and you can have them.
Gilles
2.3 Ho
Quote:
Won't find 'em.
Don't exist.
Can't be bought.
Can't even be made.
damn thats funny,
HP Tuners | Garrett T3/T04B | 2.5" Charge Pipes | 2.5" Downpipe | 650 Injectors | HO Manifold | Addco front/rear | Motor Mounts | HKS SSQV | Spec stage 3 | AEM UEGO Wideband | Team Green LSD | FMIC | 2.3 cams | 2.3 oil pump swap | 280WHP | Now ECOTECED
Mfk-223 wrote:It was a mistake. it's 2ohm 0.5Amp¸
I got a set of brown top on Ebay.
Merlin - There's a bunch of part number for the brown top. The one I got are E5ZE A3B IIRC. I gotta check. They came from an XR4TI. Give me a week and they will most likely be yours if you want them. I only need them for testing. I want to see if the injectors I have now work fine or not and you can have them.
cool, just let me know and how much you want for them!!
i was gonna buy the set on ebay right now, its a 50$ (1bid)....
I paid 50$ US + 10$ shipping for mine. I'll let you know ASAP.
Most likely this weekend. I'll try them this weekend.
Gilles
2.3 Ho
Quote:
They came from an XR4TI.
I've pulled a few sets of those injectors. Be sure and check for leaking around the top.
-->Slow
