I have been searching and looking around, and my question is...
"does MSD make an wiring harness to plug directly into my GM cavalier ICM harness then into the into the MSD?"
LD9 2.4 engine
HP Tuners | Garrett T3/T04B | 2.5" Charge Pipes | 2.5" Downpipe | 650 Injectors | HO Manifold | Addco front/rear | Motor Mounts | HKS SSQV | Spec stage 3 | AEM UEGO Wideband | Team Green LSD | FMIC | 2.3 cams | 2.3 oil pump swap | 280WHP | Now ECOTECED
No. Have fun making it work. it is possible but it'll take some work.
I used to race cars, now I race myself.
5K PB: 24:50
10K PB: 54:26
If I remember correctly, YES they do, but for the life of me, I can not find the post that has all the part numbers.
PRND321 Till I DIE
Old Motor: 160whp & 152ft/lbs, 1/4 Mile 15.4 @88.2
M45 + LD9 + 4T40-E, GO GO GO
rodimus prime figured out the wiring for the eco.....im sure the ld9 is close, contact him
My car may run 18s, but I can do your taxes in 10 seconds flat.
JBO lube - they would never have enough in stock and we'd never see RodimusPrime again
LMFAO, thanks buddy
HP Tuners | Garrett T3/T04B | 2.5" Charge Pipes | 2.5" Downpipe | 650 Injectors | HO Manifold | Addco front/rear | Motor Mounts | HKS SSQV | Spec stage 3 | AEM UEGO Wideband | Team Green LSD | FMIC | 2.3 cams | 2.3 oil pump swap | 280WHP | Now ECOTECED
Owen has an Ecotec though...and there is no wiring harness premade.
I used to race cars, now I race myself.
5K PB: 24:50
10K PB: 54:26
Team Vision Racing (aka hypsy) wrote:Owen has an Ecotec though...and there is no wiring harness premade.
Yes, but Owen ran it on his LD9 also.
# 2005's LD9
# Cosmo Racing Intake
# HO Intake
# LZM (Colt) Stage II Cams
# MSD DIS-II
# MSD Coilpacks
# Taylor 8mm Spiro Core wires
# OBX stainless header
# Casper O2 Simulator
# 2.25" Side Exit Exhaust
# Flowmaster Hushpower Muffler
PRND321 Till I DIE
Old Motor: 160whp & 152ft/lbs, 1/4 Mile 15.4 @88.2
M45 + LD9 + 4T40-E, GO GO GO
You don't have the instructions to wire it up?
If not, then go to the MSD website, go to the downloads section, and there should be a pdf file for the DIS-2 hookup.
I'll be hooking up my 6211 this weekend so wish me luck.
Good luck also in doing the hookup.
Misnblu
Misnblu.com
Newbie member since 1999
Thank you Dave and JBO! 
yah, the wiring is actually super easy to do. Only like 6-8 in, and 3 out... pretty simple, hardest part of the job, will be finding room to mount it under the hood. The Guy I bought it from said he would ship it on friday, so it should be at my place on thursday when I get home.
HP Tuners | Garrett T3/T04B | 2.5" Charge Pipes | 2.5" Downpipe | 650 Injectors | HO Manifold | Addco front/rear | Motor Mounts | HKS SSQV | Spec stage 3 | AEM UEGO Wideband | Team Green LSD | FMIC | 2.3 cams | 2.3 oil pump swap | 280WHP | Now ECOTECED
