Longer Wheel Studs - Where to Purchase/Part Numbers - Wheel and Tire Forum

Forum Post / Reply
You must log in before you can post or reply to messages.
Longer Wheel Studs - Where to Purchase/Part Numbers
Friday, February 17, 2012 2:08 PM
After much debate (new wheels, current wheels, offset, spacers) I think I've decided to pump out my current rear wheels about 1/2" to closer match the stance of the fronts. I'm gonna have spacers made for the rear and at this point ('til I go down to storage and measure tomorrow) I think .5" will be sufficient.

I've done some research on here and have seen some people post about longer wheel studs that "basically" fit with some effort. Just curious if I could get some input from people who've actually tackled this. If the current studs just hammered out of the hub after the drum was removed, what they used for longer studs and if they fit correctly. Thanks in advance, guys!!

In case you're wondering, this' a bad (but good) pic of my "dilemma:"









Re: Longer Wheel Studs - Where to Purchase/Part Numbers
Friday, February 17, 2012 2:30 PM
Well I used ARP extended camaro studs.
The knurl is a tiny bit bigger, but with a good impact gun, they will snug right into the hub.
However, if your going to install them on the front, you will need to grind the knuckle quite a bit, or remove the bearing and hub assembly.
Re: Longer Wheel Studs - Where to Purchase/Part Numbers
Saturday, February 18, 2012 7:06 AM
Why not just get hub spacers that go behind the rear hubs. A lot safer IMO



Edited 1 time(s). Last edited Saturday, February 18, 2012 10:22 AM


Re: Longer Wheel Studs - Where to Purchase/Part Numbers
Saturday, February 18, 2012 8:35 AM
^^^ Got any pics or further info?






Re: Longer Wheel Studs - Where to Purchase/Part Numbers
Saturday, February 18, 2012 8:42 AM
strat81 Online
search for jeffie's spacers in the suspension / brake forum



Re: Longer Wheel Studs - Where to Purchase/Part Numbers
Sunday, February 19, 2012 7:36 PM
this what i used with my 8mm spacers to clear my calipers. My post from quad4forums.

A stock type replacement for the BCA/National hubs are 610-445 Dorman studs. The holes in my aftermarket hubs measured 14.19mm, the new studs are 14.48mm to compensate for the crush of the old knurl. Pushed right into the hole problem free and now i have 11-12 thread engagement instead of 4-5.

Type: Serrated Stud
Thread: M12-1.5
Knurl Dia.: 14.48mm
Length: 49.19mm
Shoulder Length: 7.14mm
Head Code:
Brand: Dorman - AutoGrade - Boxed


Application Notes:
Please select Detailed Applications
for Application Note information.

SANTA FE 2006-01, TIBURON 2007-03, XG300 2001, rear

http://www.dormanproducts.com/p-15988-610-445.aspx
Reply With Quote
Re: Longer Wheel Studs - Where to Purchase/Part Numbers
Friday, February 24, 2012 10:36 AM
i used hummer h3 studs


RIP Cpl Derek Kerns And Cpl Robby Reyes
24th MEU VMM-261 (REIN) V22 Crewchiefs
11 April 2012 Morocco (African Lion)
Re: Longer Wheel Studs - Where to Purchase/Part Numbers
Friday, February 24, 2012 6:34 PM
strat81 Online
I've got arp all around. stock bearings take fbody studs. national assemblies take evo studs. (knurl diameter is larger on the national replacement hubs)



Re: Longer Wheel Studs - Where to Purchase/Part Numbers
Saturday, February 25, 2012 6:40 AM
^^^Killer info, guys--thanks








Forum Post / Reply
You must log in before you can post or reply to messages.

 

Start New Topic Advanced Search