Getrag Transmission Swap (Almost Done!) - Page 2 - Transmission Forum

Forum Post / Reply
You must log in before you can post or reply to messages.
Re: Getrag Transmission Swap (Almost Done!)
Friday, November 16, 2012 12:52 PM
Looking at the diagram, if you just connect the purple and purple/white wires from the safety switch connector from the A/T you should be fine. Just don't start the car with it already running :p.





There's 2 switches on the clutch assembly.




Edited 1 time(s). Last edited Friday, November 16, 2012 12:56 PM


I roll on steelies. Work-in-progress daily-sleeper potential.
http://www.j-body.org/classifieds/engine/60493/

Re: Getrag Transmission Swap (Almost Done!)
Thursday, January 17, 2013 6:34 AM
So... I realize how ignorant this might be but has anyone had problems mounting the clutch pedal when swapping from a 04 auto to a 04 manual? Ive found a place but it just doesn't how I think it does on one that comes stock. Can anyone post some picks of there clutch pedals (on ones that came stock manual)?

Setup:
04 2.2Eco Cav swapping getrag in.

Thanks
-plaz


You drive a cavalier? Why yes... yes I do.



Re: Getrag Transmission Swap (Almost Done!)
Thursday, January 17, 2013 6:54 AM
Stupid question, but did you drill the holes in the firewall for the clutch pedal bracket/clutch master?



Re: Getrag Transmission Swap (Almost Done!)
Thursday, January 17, 2013 7:55 AM
Tyler Ewy wrote:

Ive found a place but it just doesn't how I think it does on one that comes stock.


Well that's what I said. And why would I be asking a question regarding something I have yet to attempt? The pedal is mounted. IE It is mounted... as in it is done ready to go... as in the master/bracket are mounted. Now hopefully that was descriptive enough. What I am saying is I would like to compare my mounting job with someone else who has done it.

Sorry for being short, but I find the redundancy of saying stupid question then providing a stupid answer kind of hilarious.


You drive a cavalier? Why yes... yes I do.



Re: Getrag Transmission Swap (Almost Done!)
Thursday, January 17, 2013 11:25 AM
I didn't completely understand then.

Here's some pictures from when I was working on that part, not the greatest, but the best I have.


Here you can kind of see the clutch master hole slightly above and to the left of the hole for the wiring harness.


In one of the swap threads there are measurements for the where exactly it goes.



Re: Getrag Transmission Swap (Almost Done!)
Thursday, January 17, 2013 12:10 PM
This is what I used

http://www.j-body.org/forums/read.php?f=41&i=36216&t=36216&p=2











~2014 New Z under the knife, same heart different body~
______________________
WHITECAVY no more
2012 numbers - 4SPD AUTOMATIC!!
328 HP
306 TQ
Re: Getrag Transmission Swap (Almost Done!)
Thursday, January 17, 2013 3:03 PM
Cool thanks guys.

Nic sorry for sounding like a dick. That post came out way more "dickish" than when I first read it.




You drive a cavalier? Why yes... yes I do.



Re: Getrag Transmission Swap (Almost Done!)
Wednesday, January 23, 2013 6:34 AM
Ok guys,
I am needing the parts number for the plastic connecter between the shifting cable (black) and the shifter. Anyone now?




You drive a cavalier? Why yes... yes I do.



Re: Getrag Transmission Swap (Almost Done!)
Wednesday, January 23, 2013 7:00 AM
I think it's sold as part of the cable.


SPD RCR Z - '02 Z24 420whp
SLO GOAT - '04 GTO 305whp
RACER X - '78 Opel Kadett W41 Swap

Re: Getrag Transmission Swap (Almost Done!)
Wednesday, January 23, 2013 7:50 AM
Damn, I was afraid of that. Would anyone know the part numbers for the cables then?


You drive a cavalier? Why yes... yes I do.



Re: Getrag Transmission Swap (Almost Done!)
Wednesday, January 23, 2013 2:35 PM
I might have that piece. I'll check tomorrow.


SPD RCR Z - '02 Z24 420whp
SLO GOAT - '04 GTO 305whp
RACER X - '78 Opel Kadett W41 Swap


Forum Post / Reply
You must log in before you can post or reply to messages.

 

Start New Topic Advanced Search